Sheathing Line – Things To Consider..

No Comments

This automated optical fiber tensile testing program is ideal for operator skill independent use within production and lab configurations. Two basic model designs enable the consumer to select between a set up for regular linear evidence testing with additional mandrels for rotary high strength testing.

The linear edition is made for production proof testing with causes up to 22 N. Motor-driven clamps with very carefully designed rubberized inserts ensure that the Sheathing Line will not be ruined in the screening process whilst simultaneously eliminating the requirement for an outside air provide. Levels of tugging force, pulling speed and hold time are programmable and conveniently accessible to the owner from the built in Liquid crystal display touchscreen display manage. Information from tests can be stored and accessed via the USB dock or Ethernet user interface.

Mandrels the exact same style like NYFORS’ optical fiber recoaters can be easily mounted on the proof tester inside the rotary high strength settings. The fiber is wrapped across the two mandrels which support it having a special clamping mechanism. In this way greater loads can be used on the fiber, allowing breaking strength tests under managed circumstances.

Changeable clamp placement facilitates testing using the greatest force levels as well as screening of short fiber lengths. The lightweight and light weight style makes the tool simple to move around in a laboratory environment and also to integrate in a production work table in which space is at reasonably limited. The equipment is really a lightweight and lightweight instrument ideal for screening the strength of optical fibers approximately 30 N. The device is created to fulfill all kinds of programs in which a power check must be carried out.

The device is designed with the consumer in mind. The Sheathing Line is definitely placed in the carefully guided linear clamps, and the screening starts instantly using a “One Touch” go switch. The built-in microprocessor regulates all the essential parameters such as pulling force, pulling velocity and hold time. This enables for a completely controlled test every time.

The machine can be connected to an outside Computer, which enables usage of all programmable guidelines and settings. The machine is adapted to face-alone use or the incorporation into various subsystems. The machine has an extensive ability of logging and saving details like tugging force, pulling velocity and fiber diameter along with other parameters.

Two recoat injector designs are available. The PTR307 uses a computerized water pump to inject the recoat material. The quantity of material dispensed by the automated injector is controlled by hand via the top-installed “Inject” switch or programmed into the machine utilizing the tablet controller. The PTR307B includes a manual recoat shot program that requires the user to personally distribute the recoat materials into the mold cavity; a substitute injector for that PTR307B recoater can be obtained listed below. Please note that the automated injector is simply appropriate for higher-index recoat material, while the manual injector works with each low- and- index recoat materials; both are marketed individually listed below. Make sure you contact Tech Support for additional information.

he handbook injector can be mounted to compatible Secondary Coating Line using the 4-40 screws on the recoater housing (see photo to the right). Make use of a 3/32″ hex key to safe the injector prior to use. To connect the PTRRRM for the recoater mold, tighten up the connector at the conclusion of the green plastic tubing, then release with a 1/4 consider enable rotation.

The injector comes with a syndication valve and 2-position choice lever for directing the stream of recoat material. A knurled dispensing screw with an inner plunger acts as a syringe for your recoat materials. To fill the syringe, point the handle downward (i.e., toward the recoat container), then rotate the knurled dispensing attach counterclockwise until it rotates freely to fill up the syringe (demonstrated inside the photo towards the right). Then, to inject the recoat material to the mold, point the handle horizontally (i.e., dealing with the knurled screw) and rotate the screw clockwise till nearby the finish of the travel range is reached. Avoid bottoming out iuwekk dispenser because this may harm the inner plunger; also take care when re-interesting the threads to prevent go across threading the dispensing screw. Several fill/inject actions may be needed till air is displaced inside the system. Use lens cells as well as an acetone or alcoholic beverages cleansing solution to collect any excess recoat materials that flows through the mold.

Categories: Uncategorized

Leave a Reply

Your email address will not be published. Required fields are marked *